Go Back   V6 F-Body.com > Rides, Modifications & Racing > Other Rides > German
German For German makes

Reply
 
Thread Tools Display Modes
  #181  
Old 07-05-2018, 10:11 PM
xpbr2000's Avatar
xpbr2000 xpbr2000 is offline
Droner
LS PLUS Supporting Membership
Administrator


 
Join Date: May 2010
Location: Mooreville, MS
Rank: Freaky Poster
Posts: 11,441
Default

i've designed a 3 car garage where the center bay has a 2 post lift. I think i'm going to like it
__________________

96 Camaro Cam'd anti-Coupe
Dyno'd @ 213 RWHP (NA)
"OperationX"
Reply With Quote
  #182  
Old 07-11-2018, 12:22 PM
1973 Karmann Ghia Restoration Project's Avatar
1973 Karmann Ghia Restoration Project 1973 Karmann Ghia Restoration Project is offline
LS PLUS Supporting Membership


 
Join Date: Mar 2018
Rank: Private
Posts: 126
Default Under Hoist Stands

A pair of these (or more) are extremely handy to have, but at $130 each the cost would add up fast.



I'm thinking I can build these with some inexpensive angle iron centered around these (or something similar). I'm always down for a project. The images are links to the products.

1-1/8"-7 Hex Nut, Plain Finish, Grade 2 Steel, Right Hand



1-1/8"-7 2 ft., Threaded Rod, Steel, Grade A, Plain

__________________
Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com
Reply With Quote
  #183  
Old 07-17-2018, 07:59 AM
1973 Karmann Ghia Restoration Project's Avatar
1973 Karmann Ghia Restoration Project 1973 Karmann Ghia Restoration Project is offline
LS PLUS Supporting Membership


 
Join Date: Mar 2018
Rank: Private
Posts: 126
Default EFI System: CB's Gen4 Naturally Aspirated Kit

Even thought about stepping up to electronic fuel injection to complicate your VW's simple carbureted engine? Even though EFI does add several extra components to your system, you can't deny its benefits.

Check out this system from CB Performance ---> HERE

__________________
Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com
Reply With Quote
  #184  
Old 08-01-2018, 09:11 PM
1973 Karmann Ghia Restoration Project's Avatar
1973 Karmann Ghia Restoration Project 1973 Karmann Ghia Restoration Project is offline
LS PLUS Supporting Membership


 
Join Date: Mar 2018
Rank: Private
Posts: 126
Default 3-wire vs 4-wire Branch Feeder

3-wire feeders to detached structures that had no other parallel metallic pathways(eg. conduit, water and gas piping, communication cabling, etc.) were allowed up until the 2008 NEC code cycle.
From then on, 4-wire feeders have been required.
4-wire feeders to panels in attached structures have always been required.
3-wire feeder to detached(no longer allowed as of 2008):

4-wire feeder to detached:

4-wire feeder to attached structure:
__________________
Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com
Reply With Quote
  #185  
Old 08-10-2018, 02:29 PM
1973 Karmann Ghia Restoration Project's Avatar
1973 Karmann Ghia Restoration Project 1973 Karmann Ghia Restoration Project is offline
LS PLUS Supporting Membership


 
Join Date: Mar 2018
Rank: Private
Posts: 126
Default Engine Du Jour: CB Performance 2332cc

175 hp
180 ft/lbs. of torque
#2242 Eagle Racing Camshaft
1.25:1 Rockers
Dual 48 WEBER IDA Carb Kit
Panchito 044's w/57cc CNC Chambers
Magnaspark II Distributor
MSD Blaster 2 Coil
MSD Plug Wires
1 3/4" A-1 Low Down Exhaust w/Bombshell Muffler
5.5" Super Race Rods
#1303 Lightweight Flywheel
Stage-1 Clutch
__________________
Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com
Reply With Quote
  #186  
Old 09-01-2018, 01:58 PM
1973 Karmann Ghia Restoration Project's Avatar
1973 Karmann Ghia Restoration Project 1973 Karmann Ghia Restoration Project is offline
LS PLUS Supporting Membership


 
Join Date: Mar 2018
Rank: Private
Posts: 126
Default Portable Paint Booths by Mobile Solutions

What do you do when you need a full capable yet temporary paint booth at your location? Rent that bouncy house that was at the last birthday party your kids attended!

Well, not exactly, but along the same idea. Check out the portable paint booths by Mobile Solutions.

Mobile Solution's Website



Model MES23X15HDLT comes standard with the below features.
  • 1 23X15HDLT Fully Enclosed Portable Paint Booth
  • 12 Fresh Air Inlets Paint Booth Pads (along with covers)
  • 3 Exhaust PortablePaint Spray BoothFilters
  • 1Automobile Entrance
  • 2 Employee Entrances
  • 2 Spray Equipment Access Panels
  • 3 Rapid Air Release Slots
  • 4 Emergency Exits
  • 8 Tie Down Straps
  • 1 Storage Bag
  • 2 4000 CFM Air Movers
  • 1 Minor Repair Patch Kit
  • 1 Serial Number along with Production Date
  • 1 Year Limited Manufacture Warranty
The Exhaust filters used exceed the 98% capture efficiency. EPA 6H Rule







__________________
Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com
Reply With Quote
  #187  
Old 10-07-2018, 08:52 AM
1973 Karmann Ghia Restoration Project's Avatar
1973 Karmann Ghia Restoration Project 1973 Karmann Ghia Restoration Project is offline
LS PLUS Supporting Membership


 
Join Date: Mar 2018
Rank: Private
Posts: 126
Default Belt Grinder by Multitool

Here's a cool attachment from Multitool. It turns nearly any bench grinder into a belt and disc grinder. This could be quite handy to have in the garage.
They come in several sizes. This one is the 36x2 version.
Click Link Here



__________________
Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com
Reply With Quote
  #188  
Old 10-08-2018, 09:26 AM
xpbr2000's Avatar
xpbr2000 xpbr2000 is offline
Droner
LS PLUS Supporting Membership
Administrator


 
Join Date: May 2010
Location: Mooreville, MS
Rank: Freaky Poster
Posts: 11,441
Default

i've seen some similar to that, pretty cool way to attached it to the bench wheel. Hoping to load up my garage with some stuff, this will have to make it on a list somewhere lol
__________________

96 Camaro Cam'd anti-Coupe
Dyno'd @ 213 RWHP (NA)
"OperationX"
Reply With Quote
  #189  
Old 10-11-2018, 09:15 AM
wchiarizzio's Avatar
wchiarizzio wchiarizzio is offline


 
Join Date: Apr 2015
Rank: Sergeant
Posts: 809
Default

Yea that is pretty damn nifty I must say. Have a grinder in the shop that would be perfect on.

Sent from my SM-G930V using Tapatalk
Reply With Quote

Go Back   V6 F-Body.com > Rides, Modifications & Racing > Other Rides > German
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 10:54 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
2008 - 2018 V6F-Body.com