Page 19 of 26 FirstFirst ... 91718192021 ... LastLast
Results 181 to 190 of 259

Thread: Code Name: boneGHIA - 1973 Karmann Ghia Resoration

  1. #181
    xpbr2000's Avatar
    xpbr2000 is offline Freaky Poster LS PLUS Supporting Membership
    Administrator
    Join Date
    May 2010
    Location
    Mooreville, MS
    Posts
    11,571
    Rep Power
    100

    Default

    i've designed a 3 car garage where the center bay has a 2 post lift. I think i'm going to like it

    96 Camaro Cam'd anti-Coupe
    Dyno'd @ 213 RWHP (NA)
    OperationX thread
    OperationX blog
    FrankForged.com

  2. #182
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default Under Hoist Stands

    A pair of these (or more) are extremely handy to have, but at $130 each the cost would add up fast.



    I'm thinking I can build these with some inexpensive angle iron centered around these (or something similar). I'm always down for a project. The images are links to the products.

    1-1/8"-7 Hex Nut, Plain Finish, Grade 2 Steel, Right Hand



    1-1/8"-7 2 ft., Threaded Rod, Steel, Grade A, Plain

    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

  3. #183
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default EFI System: CB's Gen4 Naturally Aspirated Kit

    Even thought about stepping up to electronic fuel injection to complicate your VW's simple carbureted engine? Even though EFI does add several extra components to your system, you can't deny its benefits.

    Check out this system from CB Performance ---> HERE

    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

  4. #184
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default 3-wire vs 4-wire Branch Feeder

    3-wire feeders to detached structures that had no other parallel metallic pathways(eg. conduit, water and gas piping, communication cabling, etc.) were allowed up until the 2008 NEC code cycle.
    From then on, 4-wire feeders have been required.
    4-wire feeders to panels in attached structures have always been required.
    3-wire feeder to detached(no longer allowed as of 2008):

    4-wire feeder to detached:

    4-wire feeder to attached structure:
    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

  5. #185
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default Engine Du Jour: CB Performance 2332cc

    175 hp
    180 ft/lbs. of torque
    #2242 Eagle Racing Camshaft
    1.25:1 Rockers
    Dual 48 WEBER IDA Carb Kit
    Panchito 044's w/57cc CNC Chambers
    Magnaspark II Distributor
    MSD Blaster 2 Coil
    MSD Plug Wires
    1 3/4" A-1 Low Down Exhaust w/Bombshell Muffler
    5.5" Super Race Rods
    #1303 Lightweight Flywheel
    Stage-1 Clutch
    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

  6. #186
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default Portable Paint Booths by Mobile Solutions

    What do you do when you need a full capable yet temporary paint booth at your location? Rent that bouncy house that was at the last birthday party your kids attended!

    Well, not exactly, but along the same idea. Check out the portable paint booths by Mobile Solutions.

    Mobile Solution's Website



    Model MES23X15HDLT comes standard with the below features.

    • 1 23X15HDLT Fully Enclosed Portable Paint Booth
    • 12 Fresh Air Inlets Paint Booth Pads (along with covers)
    • 3 Exhaust PortablePaint Spray BoothFilters
    • 1Automobile Entrance
    • 2 Employee Entrances
    • 2 Spray Equipment Access Panels
    • 3 Rapid Air Release Slots
    • 4 Emergency Exits
    • 8 Tie Down Straps
    • 1 Storage Bag
    • 2 4000 CFM Air Movers
    • 1 Minor Repair Patch Kit
    • 1 Serial Number along with Production Date
    • 1 Year Limited Manufacture Warranty
    The Exhaust filters used exceed the 98% capture efficiency. EPA 6H Rule







    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

  7. #187
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default Belt Grinder by Multitool

    Here's a cool attachment from Multitool. It turns nearly any bench grinder into a belt and disc grinder. This could be quite handy to have in the garage.
    They come in several sizes. This one is the 36x2 version.
    Click Link Here



    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

  8. #188
    xpbr2000's Avatar
    xpbr2000 is offline Freaky Poster LS PLUS Supporting Membership
    Administrator
    Join Date
    May 2010
    Location
    Mooreville, MS
    Posts
    11,571
    Rep Power
    100

    Default

    i've seen some similar to that, pretty cool way to attached it to the bench wheel. Hoping to load up my garage with some stuff, this will have to make it on a list somewhere lol

    96 Camaro Cam'd anti-Coupe
    Dyno'd @ 213 RWHP (NA)
    OperationX thread
    OperationX blog
    FrankForged.com

  9. #189
    Join Date
    Apr 2015
    Posts
    866
    Rep Power
    9

    Default

    Yea that is pretty damn nifty I must say. Have a grinder in the shop that would be perfect on.

    Sent from my SM-G930V using Tapatalk

  10. #190
    Join Date
    Mar 2018
    Posts
    163
    Rep Power
    40014

    Default Modern Classikk Paint Line by Dave Kindig

    I recently learned Dave Kindig has partnered with AzkoNobel to create a custom paint line called Modern Classikk. I'll be keeping my eyes on this.
    Modern Classikk Website
    Check out the full 73 Karmann Ghia Restoration Blog at https://www.73ghia.com

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •